vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 1 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 phase control thyristors (hockey puk version), 1650 a features ? center amplifying gate ? metal case with ceramic insulator ? international standard case a-24 (k-puk) ? high profile hockey puk ? designed and qualified for industrial level ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 typical applications ? dc motor controls ? controlled dc power supplies ? ac controllers ? ? ? ? ? ? ? ? ? electrical specifications product summary package a-24 (k-puk) diode variation single scr i t(av) 1650 a v drm /v rrm 1200 v, 1400 v, 1600 v, 1800 v, 2000 v v tm 1.73 v i gt 100 ma t j -40 c to 125 c a-24 (k-puk) major ratings and characteristics parameter test conditions values units i t(av) 1650 a t hs 55 c i t(rms) 3080 a t hs 25 c i tsm 50 hz 30 500 a 60 hz 32 000 i 2 t 50 hz 4651 ka 2 s 60 hz 4250 v drm /v rrm 1200 to 2000 v t q typical 200 s t j -40 to 125 c voltage ratings type number voltage code v drm /v rrm , maximum repetitive peak and off-state voltage v v rsm , maximum non-repetitive peak voltage v i drm /i rrm maximum at t j = t j maximum ma vs-st1200c..k 12 1200 1300 100 14 1400 1500 16 1600 1700 18 1800 1900 20 2000 2100
vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 2 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 absolute maximum ratings parameter symbol test conditions values units maximum average on-state current ? at heatsink temperature i t(av) 180 conduction, half sine wave ? double side (single side) cooled 1650 (700) a 55 (85) c maximum rms on-state current i t(rms) dc at 25 c heatsink temp erature double side cooled 3080 a maximum peak, one-cycle ? non-repetitive surge current i tsm t = 10 ms no voltage reapplied sinusoidal half wave, ? initial t j = t j maximum 30 500 t = 8.3 ms 32 000 t = 10 ms 100 % v rrm ? reapplied 25 700 t = 8.3 ms 26 900 maximum i 2 t for fusing i 2 t t = 10 ms no voltage reapplied 4651 ka 2 s t = 8.3 ms 4250 t = 10 ms 100 % v rrm ? reapplied 3300 t = 8.3 ms 3000 maximum i 2 ? t for fusing i 2 ? t t = 0.1 ms to 10 ms, no voltage reapplied 46 510 ka 2 ? s low level value of threshold voltage v t(to)1 (16.7 % x ? x i t(av) < i < ? x i t(av) ), t j = t j maximum 0.91 v high level value of threshold voltage v t(to)2 (i > ? x i t(av) ), t j = t j maximum 1.01 low level value of on-state slope resistance r t1 (16.7 % x ? x i t(av) < i < ? x i t(av) ), t j = t j maximum 0.21 m ? high level value of on-state slope resistance r t2 (i > ? x i t(av) ), t j = t j maximum 0.19 maximum on-state voltage v tm i pk = 4000 a, t j = t j maximum, t p = 10 ms sine pulse 1.73 v maximum holding current i h t j = 25 c, anode supply 12 v resistive load 600 ma typical latchi ng current i l 1000 switching parameter symbol test co nditions values units maximum non-repe titive rate of ? rise of turned-on current di/dt gate drive 20 v, 20 ? , t r ? 1 s ? t j = t j maximum, anode voltage ? 80 % v drm 1000 a/s typical delay time t d gate current 1 a, di g /dt = 1 a/s ? v d = 0.67 % v drm , t j = 25 c 1.9 s typical turn-off time t q i tm = 550 a, t j = t j maximum, di/dt = 40 a/s, ? v r = 50 v, dv/dt = 20 v/s, gate 0 v 100 ? , t p = 500 s 200 blocking parameter symbol test conditions values units maximum critical rate of rise of ? off-state voltage dv/dt t j = t j maximum linear to 80 % rated v drm 500 v/s maximum peak reverse and ? off-state leakage current i rrm , i drm t j = t j maximum, rated v drm /v rrm applied 100 ma
vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 3 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? the table above shows the increment of thermal resistance r thjc when devices operate at different conduction angles than dc triggering parameter symbol test conditions values units typ. max. maximum peak gate power p gm t j = t j maximum, t p ? 5 ms 16 w maximum average gate power p g(av) t j = t j maximum, f = 50 hz, d% = 50 3 maximum peak positi ve gate current i gm t j = t j maximum, t p ? 5 ms 3.0 a maximum peak positive gate voltage + v gm 20 v maximum peak negative gate voltage - v gm 5.0 dc gate current required to trigger i gt t j = -40 c maximum required gate trigger/ ? current/voltage are the lowest ? value which will trigger all units 12 v anode to cathode applied 200 - ma t j = 25 c 100 200 t j = 125 c 50 - dc gate voltage required to trigger v gt t j = -40 c 1.4 - v t j = 25 c 1.1 3.0 t j = 125 c 0.9 - dc gate current not to trigger i gd t j = t j maximum maximum gate cu rrent/voltage not to trigger is the maximum value which will not trigger any unit with rated v drm anode to cathode applied 10 ma dc gate voltage not to trigger v gd 0.25 v thermal and mechanical specifications parameter symbol test conditions values units maximum operating junction ? temperature range t j -40 to 125 c maximum storage temperature range t stg -40 to 150 maximum thermal resistance, ? junction to heatsink r thj-hs dc operation single side cooled 0.0.42 k/w dc operation double side cooled 0.021 maximum thermal resistance, ? case to heatsink r thc-hs dc operation single side cooled 0.006 dc operation double side cooled 0.003 mounting force, 10 % 24 500 (2500) n (kg) approximate weight 425 g case style see dimensions - link at the end of datasheet a-24 (k-puk) ? r thjc conduction conduction angle sinusoidal conduction rectangular conduction test conditions units single side double side single side double side 180 0.003 0.003 0.002 0.002 t j = t j maximum k/w 120 0.004 0.004 0.004 0.004 90 0.005 0.005 0.005 0.005 60 0.007 0.007 0.007 0.007 30 0.012 0.012 0.012 0.012
vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 4 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - current rati ngs characteristics fig. 2 - current rati ngs characteristics fig. 3 - current rati ngs characteristics fig. 4 - current rati ngs characteristics fig. 5 - on-state powe r loss characteristics fig. 6 - on-state powe r loss characteristics average on-state current (a) maximum allowable heatsink temperature (c) 40 50 60 70 80 90 100 110 120 130 0 200 400 600 800 1000 1200 30 60 90 120 180 conduction angle st1200c..k series (single side cooled) r (dc) = 0.042 k/w thj-hs maximum allowable heatsink temperature (c) average on-state current (a) 20 30 40 50 60 70 80 90 100 110 120 130 0 400 800 1200 1600 2000 dc 30 60 90 120 180 conduction period st1200c..k series (single side cooled) r (dc) = 0.042 k/w thj-hs average on-state current (a) maximum allowable heatsink temperature (c) 30 40 50 60 70 80 90 100 110 120 130 0 400 800 1200 1600 2000 30 60 90 120 180 conduction angle st1200c..k series (double side cooled) r (dc) = 0.021 k/w thj-hs average on-state current (a) maximum allowable heatsink temperature (c) 20 30 40 50 60 70 80 90 100 110 120 130 0 600 1200 1800 2400 3000 3600 dc 30 60 90 120 180 conduction period st1200c..k series (double side cooled) r (dc) = 0.021 k/w thj-hs average on-state current (a) maximum allowable heatsink temperature (c) 0 500 1000 1500 2000 2500 3000 3500 4000 0 400 800 1200 1600 2000 180 120 90 60 30 rms limit conduction angle st1200c..k series t = 125c j maximum allowable heatsink temperature (c) average on-state current (a) 0 1000 2000 3000 4000 5000 0 600 1200 1800 2400 3000 3600 dc 180 120 90 60 30 rms limit conduction period st1200c..k series t = 125c j
vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 5 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 7 - maximum non-re petitive surge current single and double side cooled fig. 8 - maximum non-re petitive surge current single and doub le side cooled fig. 9 - on-state voltag e drop characteristics fig. 10 - thermal impedance z thj-hs characteristics number of equal amplitude half cycle current pulses (n) peak half sine wave on-state current (a) 12000 14000 16000 18000 20000 22000 24000 26000 28000 11010 0 initial t = 125c @ 60 hz 0.0083 s @ 50 hz 0.0100 s j at any rated load condition and with rated v applied following surge. rrm st1200c..k series pulse train duration (s) peak half sine wave on-state current (a) 12000 14000 16000 18000 20000 22000 24000 26000 28000 30000 32000 0.01 0.1 1 versus pulse train duration. control maximum non repetitive surge current initial t = 125c no voltage reapplied rated v reapplied j rrm of conduction may not be maintained. st1200c..k series instantaneous on-state voltage (v) instantaneous on-state current (a) 100 1000 10000 0.5 1 1.5 2 2.5 3 t = 25c j t = 125c j st1200c..k series square wave pulse duration (s) transient thermal impedance z (k/w) thj-hs 0.001 0.01 0.1 0.001 0.01 0.1 1 10 steady state value r = 0.042 k/w (single side cooled) r = 0.021 k/w (double side cooled) (dc operation) thj-hs thj-hs st1200c..k series
vs-st1200c..k series www.vishay.com vishay semiconductors revision: 09-jan-15 6 document number: 94394 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 11 - gate characteristics ordering information table instantaneous gate current (a) instantaneous gate voltage (v) 0.1 1 10 100 0.001 0.01 0.1 1 10 10 0 vgd igd (b) (a) tj=25 c tj=125 c tj=-40 c (2) a) recommended load line for b) recommended load line for <=30% rated di/dt : 10v, 10ohms frequency limited by pg(av) rated di/dt : 20v, 10ohms; tr<=1 s tr<=1 s rectangular gate pulse (3) (1) (1) pgm = 10w, tp = 4ms (2) pgm = 20w, tp = 2ms (3) pgm = 40w, tp = 1ms device: st1200c..k series - thyristor 1 - vishay semiconductors product 2 - essential part number 3 - 0 = converter grade 4 - c = ceramic puk 9 8 - critical dv/dt: 5 - voltage code: code x 100 = v rrm (see voltage ratings table) 6 - k = puk case a-24 (k-puk) 7 - 0 = eyelet terminals (gate and auxiliary cathode unsoldered leads) 1 = fast-on terminals (gate and auxiliary cathode unsoldered leads) none = 500 v/s (standard selection) l = 1000 v/s (special selection) device code 5 1 3 2 4 6 7 8 9 st vs- 120 0 c 20 k 1 - links to related documents dimensions www.vishay.com/doc?95081
document number: 95081 for tec hnical questions, contact: indmodules@vishay.com www.vishay.com revision: 02-aug-07 1 a-24 (k-puk) outline dimensions vishay semiconductors dimensions in millimeters (inches) 74.5 (2.9) dia. max. 2 holes dia. 3.5 (0.14) x 2.1 (0.1) deep 4.75 (0.2) nom. 44 (1.73) creepage distance: 28.88 (1.137) minimum strike distance: 17.99 (0.708) minimum quote between upper and lower pole pieces has to be considered after application of mounting force (see thermal and mechanical specification) 20 5 pin receptable amp. 60598-1 1 (0.04) min. 2 places 47.5 (1.87) dia. max. 2 places 27.5 (1.08) max. 67 (2.6) dia. max.
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: vishay: ? st1200c12k0p? st1200c12k1? ST1200C14K0p? st1200c16k0p? st1200c16k1? st1200c16k1l? st1200c18k0l ? st1200c18k0p? st1200c18k1? vs-st1200c20k0l? st1200c20k0lp? st1200c20k0p? st1200c20k1? st1200c20k1p? st1200c12k0? ST1200C14K0? st1200c16k0? st1200c18k0? st1200c20k0? vs-st1200c20k0
|
